Izdelki za čopič za grout (22)

Grout CR Composite , castable, anti-washout, controlled shrinkage cement mortar, superfluid consistency, based on high-resistance cements, superpozzolanic fillers (MICROSIL 90), polymeric modifiers, shrinkage resistant agents, specific additives, calcium silicate mineral fibres, selected silica aggregates. - Based on of thickened silica fume - three-dimensionally reinforced fibre with mineral and synthetic fibres - Provides high adherence and adhesion - dimensionally stable (shrinkage-compensated) - Provides high stability-physical chemical and resistance to chlorides and sulphates - suitable for underwater castings: it is anti-washout - high strength in terms of hydrostatic positive and negative thrust. Repair and protective coatings of hydraulic structures, marine and underwater structures, and articles in critical situations: harsh chemical-physical, leaching water, marine atmosphere, etc. Filling of formwork for the containment of cast immersed in sea water. In case of underwater application, the installation operations must be carried out within 8-10 hours of cleaning and "fouling" (accumulation and deposits of organic and inorganic particles on product surfaces) removal. An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). Pour 2/3 of total mixture water in the cement mixer, gradually add the product and the remaining water, until a homogeneous mixture of the required consistency is obtained. For sizable filling thicknesses, greater than 60 mm, Ghiaietto 6.10 (inert washed is selected with a particle size of from 6-10 mm) can be added in a percentage ranging from 20% to 40 %, on the basis of practical requirements. In some particularly demanding cases in terms of the resistance to the "dry-wet" cycle (for example, for the action of the tides) or for chemical attacks particularly strong, it would be advisable to add, in addition to the gravel, even thickened silica fume(MICROSIL 90), and in a variable amount depending on the thickness and construction-related need, to further improve the waterproofing and the mechanical strength of the product. In these cases, please contact our Technical Service. In the case of casts in water, make sure of perfect product hardening before removal of the formwork. Approximately 20,50 kg/m² of Grout CR for every centimetre of thickness to be implemented (approximately 2050 kg per cubic metre). Packaging: 25 kg bag UM: €/kg

2H Acryl 150 mit Quarzsand ist ein elastoplastischer Dichtstoff auf Acryldispersionsbasis für innen und außen. Einkomponentiger Acrylatdichtstoff für den Innen- und Außenbereich mit einer max. Bewegungsaufnahme von 10%. Putzähnliche Oberfläche zum Verschließen von Rissen in Putz und Mauerwerksflächen innen und außen. Verpackung in 310ml Kartusche.

COMPOSITION ET ASPECT Plâtre, carbonate de calcium, résine et divers adjuvants. La pâte est de couleur blanche. SUPPORT ADMIS Carreaux de plâtre hydrofugés ou non, plâtre, béton, agglos, béton cellulaire. REVÊTEMENTS Tous types de produits à l’exception des produits à base de ciment. DOCUMENTS À CONSULTER • DTU 25.31 • NF EN 12860 CARACTÉRISTIQUES TECHNIQUES • Temps de prise : 2h30 • Réaction au feu A1 CONDITIONNEMENTS Sacs de 5 et 25 kg sur palette houssée. STOCKAGE 9 mois en emballage d’origine non entamé à l’abri de l’humidité. PRÉPARATION DES SUPPORTS Les carreaux de plâtre doivent être secs et dépoussiérés. TAUX DE GÂCHAGE Environ 13 à 14 l. d’eau par sac de 25 kg. APPLICATION La pose du premier rang se fait en encollant le bord et le fond des mortaises venant sur le sol et en partie verticale. Les joints entre carreaux ne doivent pas dépasser 3 mm d’épaisseur. Le deuxième rang se fera de la même manière, à joints décalés, avant que la colle ait commencée...

Gomastit 701 is a painting compatible sealant based on acrylic dispersion. Suitable for slight movement joints in interior and exterior use and repair of wall cracks. Adheres to absorbent construction materials such as concrete, wood and masonry. Usage:Interior construction

Medidas disponibles 60x30x2 60x40x2 80x40x2 Otros espesores:Yes Tabla:No

DALLES DE SOL CLIPSABLES EN PVC POUR TOUS TYPES D’USAGES PROFESSIONNEL OU RÉSIDENTIEL : USINE, GARAGE, ATELIER, ENTREPÔT, BUREAU, COMMERCE ETC. LOT DE 4 DALLES = 1 M² Le système d’emboitement (queues d’aronde) breveté « en papillon » permet une solidité et une résistance incomparable. Les dalles sont assez flexibles et permettent d’épouser un sol même irrégulier. ÉPAISSEUR AU CHOIX:4MM FINITION:SURFACE LISSE

LH-241 Format: 20x20x1,6 cm3 Boite: 14 pièces - 0,56 m2 Unités: 25 tuilles/m2 Prix: 49 € TTC/m2 - Frais de transport non inclues Avant de faire votre commande, envoyez nous votre adresse de livraison pour demander les frais de transport Délais de livraison: 7 semaines info@lhmosaic.com - Wattsapp +34 625 904849

Płyty cementowo-wiórowe stosowane są w technologii „suchego montażu”. Dzięki swoim parametrom znajdują zastosowanie w budownictwie, także w elementach konstrukcyjnych. Są odporne na różne warunki atmosferyczne, takie jak mróz czy wilgoć, na działanie pleśni i grzybów, a dzięki zawartości cementu – również odporne na owady. Płyty cementowo-wiórowe to materiał sprężysty - moduł sprężystości płyt wynosi ponad 4500 N/mm2, wytrzymałość na zginanie jest większa niż 9 N/mm2.

La mosaïque est un art décoratif qui transforme des fragments de pierre colorée, d'émail, de verre, de marbre, de granito ou de céramique en motifs ou figures captivants. Chez Marque D, nous maîtrisons cet art ancien pour créer des designs uniques qui embellissent n'importe quel espace. Que ce soit pour une rénovation ou un projet neuf, notre expertise garantit un résultat qui allie tradition et modernité. Nos artisans qualifiés utilisent des techniques éprouvées pour assembler ces fragments avec précision, assurant une finition impeccable et durable. Faites confiance à notre savoir-faire pour donner vie à vos idées de décoration intérieure ou extérieure.

High temperature "moved" glass tile with medium intensity antique mirror silvering. Measurements 25x30 cm or 25x25 cm. With shiny thread. Usable for compositions.

Here we complete information about application and other features. Durability, aesthetic appearance and ease of keeping clean make these products preferred for flooring in public, industrial and commercial buildings, garages, etc. Pallets are returnable packaging. It is possible to make other tile patterns in consultation with the customer. For transport, the tiles are placed on pallets, separated by Styrofoam and covered with heat-shrinkable foil. One pallet contains 19.44 m2 of tiles Dimensions of tiles:30x30x2.8 Tiles weight:68 kg Dimensions of plinth:30x7.3x1.2 cm Plinth Weight:2 kg

Acrylic solvent base paint with good adherence, high mechanical resistance and anti slip properties. Paint for horizontal marking of floors of concrete, cement, asphalt, etc. for parking lots and areas, sidewalks, crosswalk, etc. Colours: White, Yellow (Ral 1003), Red (Ral 2002), Blue (Ral 5015).

Grout 2 HP Grout 2 HP is a pourable, fiber-reinforced mortar, used for structural restoration operations, anchoring of steel bars and strands, reinforced micropiles, tie rods, and riveting. The formulation contains very fine high-strength cements, micro-silicas with pozzolanic activity, aggregates in a rational granulometric curve (0.1 ÷ 1.8 mm), and special antisegregative additives. The product is mixed with 11% - 12% of water, requiring vigorous and prolonged mechanical mixing. The special formulation of Grout 2 HP provides the castings with mechanical strength, fracture energy, exceptional durability, and very high chemical-physical resistance. Grout 2 HP has a workability time of about 60-90 minutes, after which the setting process is triggered, followed by progressive hardening. The plastic and hygrometric shrinkage is extremely low thanks to the presence of Readymesh PM-060 multifilament synthetic fibers, which provide volumetric stability. The performances that make Grout 2 HP unique are: • very high compressive mechanical strengths (> 90 MPa at 28 days), • very high mechanical resistance to bending-traction (> 12 MPa after 28 days), • excellent durability and resistance to chemical attacks. Grout 2 HP is used for structural restoration operations, anchoring of steel bars and strands, reinforced micropiles, tie rods, and riveting. It is particularly suitable for operations where high mechanical performance is required after short curing (compressive strength at 3 days > 60 MPa) and in operations carried out in severe exposure environments (XC - XS - XF), characterized by aggression from sulphates, chlorides, and nitrates. The material can also be used for repairs in anchoring areas subject to high stresses. The application surfaces must be clean, free of dirt, crumbly and incoherent parts, dust, etc., and suitably saturated with water until reaching the condition of "saturated with dry surface". Adequate roughening of the surfaces by scarifying, sandblasting, etc. is always necessary to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). It is strongly recommended, for optimal performance of site operations, to use a vertical axis mixer with planetary movement or a double horizontal helicoid. The powder is mixed with drinking water to the extent of 11% - 12%, referring to the total weight of the mortar (about 2.75 liters per 25 kg bag) until a homogeneous mixture is obtained. Mixing time: about 4 minutes with a high efficiency mixer. The anchoring can be filled with a single screw pump, for mortars. Pumping must be carried out at a controlled speed to ensure a low working pressure. In case of restorations, the surface must be protected, after application, by polyethylene sheets or anti-evaporation treatments. Packaging: 25 kg bag Unit of Measure: €/kg

DÉFINITION TECHNIQUE Enduit décoratif à projeter en pâte prête à l’emploi pour un usage en murs et plafonds intérieurs. Permet de rattraper dans une certaine mesure les défauts du support tels que bullages et balèvres. Peut être appliqué en tant qu’enduit de lissage ou en relief structuré type « gouttelette ». Différentes teintes et qualité lavable sur demande. DOCUMENTS À CONSULTER DTU 59.1. PV CSTB N°R.A.97.179 : classement au feu MO. COMPOSITION ET ASPECT Résine acrylique en émulsion, charge minérale, dérivés cellulosique, agent de conservation et divers adjuvants. La pâte est de couleur blanche et de consistance adaptée à la projection mécanique. CARACTÉRISTIQUES TECHNIQUES • Extrait sac : 72% • Densité : 1,6 SUPPORTS ADMIS Béton plus ou moins bullé, béton brut de décoffrage, béton cellulaire, carreaux de terre cuite, première couche lissée de SOLIDECOR, agglos, enduits plâtre, anciennes peintures, enduit ciment, carreaux de plâtre, plaques de...

Carreaux ciment artisanal, motif classique Andalous en format carrée de 20x20x1,6 cm3 pour sol et mur. Format: 20x20x1,6 cm3 Boite: 14 pièces - 0,56 m2 Unités: 25 tuilles/m2 Prix: 56 € TTC/m2 - Frais de transport non inclus Avant de faire votre commande, envoyez nous votre adresse de livraison pour demander les frais de transport Delais de Livraison: 6 semaines

Gomastit Spiegelkleber is an elastic adhesive based on SMP. Adheres mirrors and coated glass perfectly on various construction materials inclusive plastics. Usage:Sanitary, Interior construction

Medidas disponibles 60x30x2 40x30x2 30x30x2 60x40x2 60x60x2 40x40x2 80x40x2 80x80x2 100x100x2 120x120x2 Otros espesores:Yes Tabla:Yes

LH-380

Gomastit 407 is a sealant based purely on silicone for joints in the natural stone and parquet area, as well as for connections of various construction materials. Gomastit 407 is mouldresistant, as well as UV and weather resistant. This product is easy to process and ensures durable sealing. Gomastit 407 is mechanically resilient and can be walked on. Usage:Facades, Sanitary, Interior construction, Floor

LH-370

LH-320

LH-702